201,3 грн

HYPERSEAL®-EXPERT-150 – Polyurethane hybrid sealant of a new generation for sealing and sealing joints. One-component paste-like material based on polyurethane. It polymerizes under the influence of air humidity.
   Low modulus sealant with Shore A25 hardness. Non-toxic after polymerization. Resistant to ultraviolet radiation.
   Due to its special hybrid composition, it has excellent adhesion on surfaces traditionally problematic for polyurethane sealants, for example, glass, aluminum, steel, polycarbonate, etc.
   The sealant is easy to apply even at low temperatures. HYPERSEAL®-EXPERT-150
Application conditions
type of foundation
Concrete, polymer cement mixtures, metal, glass, wood, etc.
Base strength
R28 = 25 MPa (minimum 15 MPa)
Base moisture
W <10%
Air humidity
W <85%
Operating Temperature (Tvozd, Tosn)
5 ° C – 35 ° C, 3 ° C above the dew point ** It is allowed to apply sealant at low temperatures (up to -15 ° C). The necessary conditions for this are: holding the sealant before starting work in a warm room (for convenience of work) and a dry surface (no frost). The polymerization time increases.
Consumption rate
100 ml / rm (with a seam section 1 cm2)
600ml tubes
White, gray, black, beige
Shelf life
At least 12 months (at 5-25 ° C in a dry and ventilated area)
Material properties:
Dry residue
Consistency before curing
Thixotropic viscous mass
Density (20 ° C)
1.45 g / cm2
Time of formation of the surface film (25 ° C, W = 55%)
2.5-3.5 hours
Polymerization rate
2-3 mm / day (depending on temperature and humidity)Sealant properties:
Operating temperature
– 40 ° C – + 80 ° C
Maximum short-term temperature
+ 120 ° C
25 Shore A
Modulus of elasticity at 100% tensile
3.0 kg / cm2
Elasticity (elongation to break)
> 700%
Adhesion to concrete
> 20 kg / cm2
Temperature stability (100 days at 80 ° C)
Accelerated Aging Test
> 2000 h
None after complete polymerization
Test for alkali resistance (8% KOH, 15 days at 50 ° C)
No change in elasticity
Test for resistance to water (H2O, 30-day cycles of 60-100 ° C)
No change in elasticity
Acid Resistance Test (PH = 2, 10 days @RT)
No change in elasticity
Certified Quality


  • Filling of structural and expansion joints in reinforced concrete, metal, wood and combined structures of any complexity: interpanel joints of buildings, roofs, irrigation and drainage and hydraulic structures, pools, reservoirs, tunnels, retaining walls, bridges, airfields, timber houses.
  • Reliably and flexibly (dynamically) connects and seals dissimilar building materials – concrete, metal, ceramics, glass, wood and others.
  • Can be used in direct contact with drinking water and food. For exterior and interior. It has improved adhesion to materials  traditionally problematic – glass, aluminum, polycarbonate and other plastics.Sealing of joints:
    • In concrete; 
    • Precast reinforced concrete; 
    • masonry; 
    • water tanks; 
    • Aluminum windows and panels; 
    • Sandwich panels; 
    • Granite and marble
    • No defects in the internal structure (bubbles) during polymerization in complexclimatic conditions;
    • Excellent thixotropy;
    • Excellent adhesion to almost any surface type using or  without the use of special primers;
    • Excellent working properties in wide range of climatic conditions;
    • Excellent chemical resistance;
    • Resistant to microorganisms and fungi;
    • Excellent heat resistance, suitable for use with constant exposure  temperatures> 60 ° C;
    • Resistance to cold: Sealant remains elastic even to -40oC. Not recommended for use under  direct sunlight.

Additional information

Под заказ



There are no reviews yet.

Be the first to review “Sealant HYPERSEAL®- EXPERT-150”

Your email address will not be published. Required fields are marked *