Sealant HYPERSEAL®-25LM gray and white
HYPERSEAL®-25LM - Polyurethane hybrid sealant of a new generation for sealing and sealing joints. One-component paste-like material based on polyurethane. It polymerizes under the influence of air humidity.
Low modulus sealant with Shore A25 hardness. Non-toxic after polymerization. Resistant to ultraviolet radiation.
Due to its special hybrid composition, it has excellent adhesion on surfaces traditionally problematic for polyurethane sealants, for example, glass, aluminum, steel, polycarbonate, etc.
The sealant is easy to apply even at low temperatures.
Sealant HYPERSEAL®- EXPERT-150
HYPERSEAL®-EXPERT-150 - Polyurethane hybrid sealant of a new generation for sealing and sealing joints. One-component paste-like material based on polyurethane. It polymerizes under the influence of air humidity.
Low modulus sealant with Shore A25 hardness. Non-toxic after polymerization. Resistant to ultraviolet radiation.
Due to its special hybrid composition, it has excellent adhesion on surfaces traditionally problematic for polyurethane sealants, for example, glass, aluminum, steel, polycarbonate, etc.
The sealant is easy to apply even at low temperatures. HYPERSEAL®-EXPERT-150
Application conditions
type of foundation
Concrete, polymer cement mixtures, metal, glass, wood, etc.
Base strength
R28 = 25 MPa (minimum 15 MPa)
Base moisture
W <10%
Air humidity
W <85%
Operating Temperature (Tvozd, Tosn)
5 ° C - 35 ° C, 3 ° C above the dew point ** It is allowed to apply sealant at low temperatures (up to -15 ° C). The necessary conditions for this are: holding the sealant before starting work in a warm room (for convenience of work) and a dry surface (no frost). The polymerization time increases.
Consumption:
Consumption rate
100 ml / rm (with a seam section 1 cm2)
Specifications:
Packaging
600ml tubes
Colour
White, gray, black, beige
Shelf life
At least 12 months (at 5-25 ° C in a dry and ventilated area)
Material properties:
Dry residue
100%
Consistency before curing
Thixotropic viscous mass
Density (20 ° C)
1.45 g / cm2
Time of formation of the surface film (25 ° C, W = 55%)
2.5-3.5 hours
Polymerization rate
2-3 mm / day (depending on temperature and humidity)Sealant properties:
Operating temperature
- 40 ° C - + 80 ° C
Maximum short-term temperature
+ 120 ° C
Hardness
25 Shore A
Modulus of elasticity at 100% tensile
3.0 kg / cm2
Elasticity (elongation to break)
> 700%
Adhesion to concrete
> 20 kg / cm2
Temperature stability (100 days at 80 ° C)
sustained
Accelerated Aging Test
> 2000 h
Toxicity
None after complete polymerization
Test for alkali resistance (8% KOH, 15 days at 50 ° C)
No change in elasticity
Test for resistance to water (H2O, 30-day cycles of 60-100 ° C)
No change in elasticity
Acid Resistance Test (PH = 2, 10 days @RT)
No change in elasticity
Certified Quality
HYPERDESMO ® -D 5l.
HYPERDESMO ® -D - one-component liquid material based on elastic polyurethane resins. Polymerizes under the influence of humidity, forming a seamless durable elastic covering.
Application area:
- To protect and prevent corrosion of concrete, mosaic, metal, ceramics, wood and other building materials.
- Creation of non-dusting, antibacterial, hygienic, anti-slip, sparkles and decorative industrial flooring that can withstand light and medium loads (parking lots, warehouses, cold rooms, industrial premises, hospitals, etc.).
- Surface treatment and protection: tanks and storages with chemically, biologically and radiation-aggressive products, as well as sewage treatment plants.
- Sheeting in the food industry, the chemical industry, pharmaceutics, health care, power and mechanical engineering.
- Sealing, painting, hydrophilization of complex iron-concrete structures and elements.
- Chemically finishing and wear-resistant layer in waterproofing systems.
Primer MICROSEALER-PU 5 Л.
Microsealer-PU - is a one-component, consisting of 100% solid particles, polyurethane primer, ideal for almost any basis. The material has a low viscosity and excellent impregnating properties, ideal for wet or dry concrete. Moreover, the material is ideally suited for both porous and non-porous smooth surfaces, such as glass, polished aluminum or metal surfaces.
It has excellent mechanical properties and high elasticity — the elongation of the film is 400%, which is comparable to the Hyperdesmo® product line, and the tensile strength is more than 20 N / mm2.
Microsealer-PU can be used on wet or "green" concrete, not only as a primer, but also as an impregnation, giving concrete durability.
Apply with brush or roller. Consumption: 100-500 g / m2, depending on the porosity of the base.
Mastic HYPERDESMO®-H.A.A. 25 kg
HYPERDESMO®-H.A.A. - unique polyurethane mastic for reliable waterproofing and protection. Based on the successful combination of Hyperdesmo and Accelerator-3000A, which makes it possible to apply mastic in thicker layers without the formation of bubbles, and also accelerates the polymerization process.
Accelerator-3000A is turned on in a blocked state so that when it comes into contact with moisture it is released and automatically accelerates the process of polymerization of the material.
Due to the unique composition of HYPERDESMO®-H.A.A. It quickly polymerizes without the formation of internal membrane defects with excellent physic mechanical and operational abilities.
In addition, to achieve the minimum required thickness of the waterproofing membrane HYPERDESMO®-H.A.A. can be applied with fewer layers, which reduces labor costs.
Apply with a brush, roller or airless sprayer in one or two layers with a minimum total consumption of 1.5-2.0 kg / m2
UNIVERSAL PRIMER-2K-406
UNIVERSAL PRIMER-2K-4060 is a two-component, solvent-free polyurethane primer for HYPERDESMO® products and other Alchimica® polyurethane coatings. It is a rapidly polymerizing primer, free of toxic and volatile organic matter, which was developed for application to dry or wet concrete or other bases. Provides reliable adhesion of polyurethane coatings with the base.
floors HYPERFLOOR® -2K Grey
HYPERFLOOR® -2K is a two-component material based on pure polyurethane resins with inorganic additives that provide high abrasion resistance of the coating. It cures after mixing the components, forming a seamless durable elastic coating. Does not contain organic solvents.
Mastic HYPERDESMO-PB-1K (20 кг)
Weight 20kg.
Used for:
gypsum and cement slabs,
asphalt membranes (also for repair),
roof insulation,
cement surfaces,
waterproofing of a light roof from metal or fiber cement
basement insulation,
foundations,
indoor areas with high humidity.
Detailed characteristics: Hyperdesmo-PB-1K
Primer MICROSEALER-PU 20 Kg.
Microsealer-PU - is a one-component, consisting of 100% solid particles, polyurethane primer, ideal for almost any basis. The material has a low viscosity and excellent impregnating properties, ideal for wet or dry concrete. Moreover, the material is ideally suited for both porous and non-porous smooth surfaces, such as glass, polished aluminum or metal surfaces.
It has excellent mechanical properties and high elasticity — the elongation of the film is 400%, which is comparable to the Hyperdesmo® product line, and the tensile strength is more than 20 N / mm2.
Microsealer-PU can be used on wet or "green" concrete, not only as a primer, but also as an impregnation, giving concrete durability.
Apply with brush or roller. Consumption: 100-500 g / m2, depending on the porosity of the base.
Primer water-based AQUADUR 10 kg.
Aquadur is a two-component water-based epoxy water-borne emulsion system. It is used as a primer in preparing the base for HYPERDESMO® systems or independently as a protective coating.
Does not contain volatile organic solvents - can be used in poorly ventilated areas. May be diluted with water.
Ideal for use in conditions of negative pressure and high humidity.
It is also effectively used as a vapor barrier.
VARNISH HYPERDESMO®-ADY-E 20
HYPERDESMO®-ADY-E - is a single-component polyurethane lacquer, which polymerizes under the influence of atmospheric humidity, forming a transparent membrane of increased elasticity with excellent uniform adhesion over the entire surface. The varnish is completely aliphatic: there is no yellowing and color change as a result of direct exposure to sunlight. It is the ideal solution for protecting HYPERDESMO® color.
Based on pure elastomeric hydrophobic polyurethane resins, with the result that it has excellent resistance to mechanical, chemical, thermal and other influences.
Excellently colored with Alchimica® pigment pastes.
Apply by brush, roller or airless spray in one or more layers. Minimum consumption per layer: 0.1 kg / m2.
VARNISH HYPERDESMO®-ADY-E 20 l.
HYPERDESMO®-ADY-E - is a single-component polyurethane lacquer, which polymerizes under the influence of atmospheric humidity, forming a transparent membrane of increased elasticity with excellent uniform adhesion over the entire surface. The varnish is completely aliphatic: there is no yellowing and color change as a result of direct exposure to sunlight. It is the ideal solution for protecting HYPERDESMO® color.
Based on pure elastomeric hydrophobic polyurethane resins, with the result that it has excellent resistance to mechanical, chemical, thermal and other influences.
Excellently colored with Alchimica® pigment pastes.
Apply by brush, roller or airless spray in one or more layers. Minimum consumption per layer: 0.1 kg / m2.